Source | Target | Programmable displays with a wide selection of inputs and outputs for display of temperature, volume and weight, etc. | Programowalne wyświetlacze z szerokim wyborem wejść i wyjść do pokazywania temperatury, objętości, masy, itd. |
PC or front programmable modules with universal options for input, output and supply. | Moduły z wyświetlaczem PC lub frontowym z uniwersalnymi opcjami wejścia, wyjścia i zasilania. |
Visualisation in the 4501 of sensor error detection and input signal outside range. | Wizualizacja w 4501 wykrycia błędu czujnika i sygnału wejściowego poza zakresem. |
Descriptions of input/output and supply connections are shown in the block diagram and side label. | Opis zacisków wejścia, wyjścia oraz zasilania pokazany jest na schemacie oraz z boku obudowy modułu. |
Input for RTD, TC, Ohm, potentiometer, mA and V | Wejście RTD, TC, Ohm, mA, V i potencjometr |
Input signals | Sygnały wejściowe |
Temperature input | Wejście temperaturowe |
mA/V input | Wejście mA/V |
Input type | Typ wejścia |
RTD, linear resistance and potentiometer input | Wejście RTD, liniowej rezystancji i potencjometryczne |
Input RTD types | Typy wejścia RTD |
TC input | Wejście termoparowe |
Current input | Wejście prądowe |
Input resistance | Rezystancja wejściowa |
Voltage input | Wejście napięciowe |
Visualisation in the 4501 of sensor error detection and input signal outside range | Wizualizacja wykrycia błędu czujnika w 4501 i sygnał wejściowy, przy którym przetwornik przechodzi w stan "przekroczenia zakresu" |
Input | Wejście |
Check that input signal match input configuration | Test czy sygnał wejściowy jest dopasowany do konfiguracji wejścia |
1) Error levels on input | 1) Błędy na wejściu |
Inputs | Wejścia |
Signals outside the selected range (not sensor error, see table for limits) are displayed as IN.LO indicating low input signal or IN.HI indicating high input signal. | Jeżeli sygnał wejściowy jest większy niż ustawiony zakres (nie błąd czujnika, limity - patrz tabela) wyświetlany jest komunikat IN.LO jeżeli sygnał jest niższy lub IN.HI jeżeli sygnał jest wyższy. |
A low input signal (not necessarily 0%) is applied and the actual value is entered. | Ustawia się niski sygnał wejściowy (niekoniecznie na poziomie 0%) i zapisuje rzeczywistą wartość. |
If you later reject this menu point or choose another type of input signal the unit will return to factory calibration. | W przypadku braku zatwierdzenia lub wybraniu innego typu sygnału wejściowego, urządzenie powróci do ustawień fabrycznych. |
Process simulation function: If you agree to the point EN.SIM it is possible to simulate an input signal by means of the arrow keys and thus control the output signal up or down. | Symulacja wejścia: Wybierając YES w punkcie EN.SIM możemy symulować sygnał wejściowy i zmieniać go za pomocą strzałek góra/dół. |
IN.ER - Error levels on input | IN.ER - Błąd typu wejścia |
After choosing the input signal type you can choose which process units should be displayed in text line 2 (see table). | Po wybraniu typu sygnału wejściowego, można dokonać wyboru aktualnej jednostki, która ma być wyświetlana w 2 linijce (patrz tabela). |
By selection of temperature input the process value is always displayed in Celsius or Fahrenheit. | Wartość procesu wejścia temperaturowego zawsze jest pokazywana w stopniach Celsjusza lub Fahrenheita. |
This is selected in the menu point after selection of temperature input. | Wybór jednostki odbywa się po ustawieniu wejścia temp. w menu. |
Line 1 shows input signal. | W 1 wierszu sygnał wejściowy. |
1.2 = not valid for these input signals | 1.2 = nie obowiązuje dla tych sygnałów wejściowych |
1.3 = only if input signal is temperaure. | 1.3 = tylko jeśli sygnałem wejściowym jest temperatura. |
Enter advanced setup menu? | Wejść do menu zaawansowanego? |
Select temperature input | Wybór wejścia temperaturowego |
Select potentiometer input | Wybór wejścia potencjometrycznego |
Select linear resistance input | Wybór wejścia oporowego liniowego |
Select current input | Wybór wejścia prądowego |
Select voltage input | Wybór wejścia napięciowego |
Select 0.0-1 V input range | Wybór zakresu wejścia 0.0-1 V |
Enter password setup | Wejście do ustawień hasła |
Enter simulation mode | Wejście do ustawień symulacji |
Enter display setup | Wejście do ustawień wyświetlacza |
Perform memory operations | Wejście do ustawień pamięci |
Set the input simulation value | Wprowadzić symulowaną wartość wejścia |